DKM clutch VW Golf III IV Polo 9N 6R 1.6 1.9TDI - 1020Nm DK-MR-034-141

MR Twin Disc Clutch Kits are ideal for high powered vehicles. Constructed of molded clamp for increased stiffness. The additional contact surface provided by the two ceramic couplings and the smaller diameter reduce the moment of inertia (Mole), thus maximizing the acceleration characteristics of the motor. MR clutch kits are able to hold a wheel torque of 1020Nm. Each set consists of a cast pressure plate, ceramic discs and a steel flywheel. Additional parts such as bearing / guide bushing, release bearing (included if applicable) and a setting tool are also included. Recommended for high power racing car applications CNC machined parts Two 184mm ceramic discs Rated torque over 1000Nm Steel flywheel Fits: AUDI A1 8X1, 8XK 1.6 TDI (05.2010-04.2011) AUDI A3 8L1 1.9 TDI (10.2000- 05.2003) SEAT CORDOBA 6K1, 6K2, 6K5 1.9 TDI (03.1997-12.2002) SEAT IBIZA 6K1 1.9 TDI (03.1997-12.2002) SEAT IBIZA 6J1, 6J5, 6P1, 6P5 1.6 TDI, ST 1.6 TDI (05.2009- 11.2010) SEAT IBIZA 6J1, 6J5, 6P1, 6P5 1.9 TDI (03.2008-06.2010) SEAT LEON 1M1 1.9 TDI (11.1999-06.2006) SEAT TOLEDO 1L 1.9 TDI (11.1996-03.1999) SEAT TOLEDO 1M2 1.9 TDI (10.1998-07.2004) SKODA FABIA 542, 545 1.6 TDI, ST 1.6 TDI (03.2010-10.2010) SKODA OCTAVIA 1U2, 1U5 1.9 TDI (07.1996-12.2010) SKODA OCTAVIA 1U2, 1U5 1.9 TDI 4X4 (11.1999 -02.2006) SKODA OCTAVIA 1U2, 1U5 1.9 TDI (08.2000-12.2010) VW BEETLE 9C1, 1C1, 1Y7 1.9 TDI (01.1998-09.2010) VW BORA 1J2, 1J6 1.9 TDI, 1.9 TDI 4-MOTION (10.1998 -05.2005) VW GOLF III 1E7, 1H1 1.9 TDI, 1.9 TDI SYNCHRO (08.1995-04.1999) VW GOLF III CABRIOLET 1E7 1.9 TDI (08.1995-04.1999) VW GOLF IV 1J1 1.9 TDI, 1.9 TDI 4-MOTION (05.1999-05.2006) VW PASSAT 3A2, 3A5, 35L 1.9 TDI (03.1996-05.1997) VW POLO 6V2, 6V5 1.9 TDI (09.1996-01.2002) VW POLO 9N 1.9TDI (10.2001-11.2009) VW POLO 6R 1.6 TDI (06.2009-10.2010) VW VENTO 1H2 1.9 TDI (04.1996-09.1998) MR Twin Disc Clutch Kits are ideal for high-powered vehicles. Constructed of billet pressure plate for increased stiffness and no clamp-load deflection. The additional contact surface area provided by the two cerametallic disc setup and smaller diameter result in reducing the moment of inertia (Mol), thereby maximizing the engine acceleration characteristics. MR Clutch Kits are able to hold 650 ft / lbs of wheel torque. Each kit is comprised of a billet pressure plate, cerametallic discs and steel flywheel. Additional parts such as pilot bearing / bushing, throw-out bearing (are included when applicable) and alignment tool are also included. Recommended for high horsepower race car applications CNC machined components 184mm dual ceramic disc setup Rated for upwards of 650 ft / lbs of torque Chromoly steel flywheelsFits: AUDI A1 8X1, 8XK 1.6 TDI (05.2010-04.2011) AUDI A3 8L1 1.9 TDI (10.2000 -05.2003) SEAT CORDOBA 6K1, 6K2, 6K5 1.9 TDI (03.1997-12.2002) SEAT IBIZA 6K1 1.9 TDI (03.1997-12.2002) SEAT IBIZA 6J1, 6J5, 6P1, 6P5 1.6 TDI, ST 1.6 TDI (05.2009 -11.2010) SEAT IBIZA 6J1, 6J5, 6P1, 6P5 1.9 TDI (03.2008-06.2010) SEAT LEON 1M1 1.9 TDI (11.1999-06.2006) SEAT TOLEDO 1L 1.9 TDI (11.1996-03.1999) SEAT TOLEDO 1M2 1.9 TDI (10.1998-07.2004) SKODA FABIA 542, 545 1.6 TDI, ST 1.6 TDI (03.2010-10.2010) SKODA OCTAVIA 1U2, 1U5 1.9 TDI (07.1996-12.2010) SKODA OCTAVIA 1U2, 1U5 1.9 TDI 4X4 ( 11.1999-02.2006) SKODA OCTAVIA 1U2, 1U5 1.9 TDI (08.2000-12.2010) VW BEETLE 9C1, 1C1, 1Y7 1.9 TDI (01.1998-09.2010) VW BORA 1J2, 1J6 1.9 TDI, 1.9 TDI 4-MOTION ( 10.1998-05.2005) VW GOLF III 1E7, 1H1 1.9 TDI, 1.9 TDI SYNCHRO ( 08.1995-04.1999) VW GOLF III CABRIOLET 1E7 1.9 TDI (08.1995-04.1999) VW GOLF IV 1J1 1.9 TDI, 1.9 TDI 4-MOTION (05.1999-05.2006) VW PASSAT 3A2, 3A5, 35L 1.9 TDI (03.1996 -05.1997) VW POLO 6V2, 6V5 1.9 TDI (09.1996-01.2002) VW POLO 9N 1.9TDI (10.2001-11.2009) VW POLO 6R 1.6 TDI (06.2009-10.2010) VW VENTO 1H2 1.9 TDI (04.1996 -09.1998) MR Twin Disc Clutch Kits are ideal for high powered vehicles. Constructed of molded clamp for increased stiffness. The additional contact surface provided by the two ceramic couplings and the smaller diameter reduce the moment of inertia (Mole), thus maximizing the acceleration characteristics of the motor. MR clutch kits are able to hold a wheel torque of 1020Nm. Each set consists of a cast pressure plate, ceramic discs and a steel flywheel. Additional parts such as bearing / guide bushing, release bearing (included if applicable) and a setting tool are also included. Recommended for high power racing car applications CNC machined parts Two 184mm ceramic discs Rated torque above 1000Nm Steel flywheel & nbsp